I recently upgraded my main machine at home. That means my old system got relegated to server status. It is a 4770k with an ASUS board with dual NICs.
I set up the home distribution as I want to incorporate plex into the build. The issue that I'm having is that I keep getting lag spikes on the network when going through the gateway. It happens on wifi and on wired LAN. The wifi is through two Unifi APs that I have setup.
The lag spikes seem random. When watching Amazon Prime or youtube it is annoying, but while gaming it is VERY frustrating. When I say lag spikes I mean no connection for 15-20 seconds. Some games just drop me, other just lag and then come back. The streaming video is the same. Sometimes I even have to close down roku/youtube in order to get the connection back.
I have 250 megabits down and 10 megabits up from my ISP. I've tried with my cable modem with bridge mode both on and off.
Both of my nics on my motherboard are gigabit. One is an Intel and the other is a realtek I think.
This is definitely a game breaker if I can't get this to work properly.
I set up the home distribution as I want to incorporate plex into the build. The issue that I'm having is that I keep getting lag spikes on the network when going through the gateway. It happens on wifi and on wired LAN. The wifi is through two Unifi APs that I have setup.
The lag spikes seem random. When watching Amazon Prime or youtube it is annoying, but while gaming it is VERY frustrating. When I say lag spikes I mean no connection for 15-20 seconds. Some games just drop me, other just lag and then come back. The streaming video is the same. Sometimes I even have to close down roku/youtube in order to get the connection back.
I have 250 megabits down and 10 megabits up from my ISP. I've tried with my cable modem with bridge mode both on and off.
Both of my nics on my motherboard are gigabit. One is an Intel and the other is a realtek I think.
This is definitely a game breaker if I can't get this to work properly.
Share this post:
Responses (11)
-
Accepted Answer
# lspci -k | grep Eth -A 3
00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-V (rev 04)
Subsystem: ASUSTeK Computer Inc. Device 859f
Kernel driver in use: e1000e
Kernel modules: e1000e
--
08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 859e
Kernel driver in use: r8169
Kernel modules: r8169
Here is the output. -
Accepted Answer
-
Accepted Answer
I installed the new driver and did a reboot. not 100% sure but I think I'm still having the disconnect issues. Here is the output from the lspci command. The r8169 has been rolled back according to this.
lspci -k | grep Eth -A 3
00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-V (rev 0 4)
Subsystem: ASUSTeK Computer Inc. Device 859f
Kernel driver in use: e1000e
Kernel modules: e1000e
--
08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 P CI Express Gigabit Ethernet Controller (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 859e
Kernel driver in use: r8168
Kernel modules: r8168
Going to check a few more things, but I did just get disconnected from a game. It could have been a random DC because they do happen, but I haven't had one here in a long time and I'm on wired LAN, not WiFi -
Accepted Answer
-
Accepted Answer
-
Accepted Answer
-
Accepted Answer
I think this is solved but I'll report back in a few days. BIOS was up to date. I swapped the connections so my WAN connection is on the INTEL NIC and my LAN is on the other.
I am seeing some other strange behavior I think.
From my computer on the LAN I can ping and log into my cable modem just by typing in its IP address even though my computer is showing it to be on the LAN subnet and not the cable modem subnet.
I do not have my cable modem in bridge mode.
my computer is 10.10.10.x
clear gateway
LAN: 10.10.10.1
WAN: 10.0.0.x
cable modem is 10.0.0.1
if I type 10.0.0.1 in my address bar it goes to the cable modem config. I can also ping that IP address with windows command line.
Not sure exactly what is happening here, but it seems fishy. -
Accepted Answer
-
Accepted Answer
So I'm not sure, but I think that was two commands...anyways, here are the outputs from them.
# ifconfig |grep '^\S' -A 1
eno1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.0.0.141 netmask 255.255.255.0 broadcast 10.0.0.255
--
enp8s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.10.10.1 netmask 255.255.255.0 broadcast 10.10.10.255
--
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
# cat /etc/clearos/network.conf
# Network mode
MODE="gateway"
# Network interface roles
EXTIF="eno1"
LANIF="enp8s0"
DMZIF=""
HOTIF=""
# Domain and Internet Hostname
DEFAULT_DOMAIN="neezergaming.com"
INTERNET_HOSTNAME="neezergaming.com"
# Extra LANS
EXTRALANS=""
# ISP Maximum Speeds
ENO1_MAX_DOWNSTREAM=0
ENO1_MAX_UPSTREAM=0
ENP8S0_MAX_DOWNSTREAM=0
ENP8S0_MAX_UPSTREAM=0 -
Accepted Answer
Please login to post a reply
You will need to be logged in to be able to post a reply. Login using the form on the right or register an account if you are new here.
Register Here »